Equipment: Cartridge Collector with cellulose Media, 8 pleats per inch.
Application: System designed to coat outside surfaces of gloves with starch to keep them from sticking together. It was effective and was meant for surgical use. The coating readily fell off the gloves when they were worn and before they were put to use.
Observations: The starch dust was very coarse in the 5 to 10 micron size. The dust would easily fall from the fingers when squeezed and moved together. When the system pulsed large puffs of dust were observed at the collector outlet. We examined the dust under the microscope and it was uniform in size in the 5 to 10 micron range. However, the surface of the dust particle spheres were very smooth, almost polished. The collector ran with less than one inch pressure drop across the media, the same pressure drop as a clean cartridge. The lack of the ability to interlock the dust to form a cake meant that, during pulsing, the dust would tumble and could not agglomerate and this allowed the dust to penetrate the media during and after a cleaning cycle. The collector exhaust was returned to the work space, dust and all.
Recommendations, action, remedy and conclusions.We recommended adding a small amount of ordinary cornstarch into the collector on an intermittent basis, once every four hours. This ordinary powdered (non-spheroidal) starch formed a stable filter cake and the collector ran at 2 inches of pressure drop across the media, solving the penetration problem. The contaminated starch collected from the hopper was then sold for animal consumption but it was not a significant cost for the process. Another solution was to use a standard tubular shaker collector with laminated (Gortex) media which does not require interlocking dust to form a cake.
This approach is suitable for other dusts that do not form granulated powders that don't interlock to form a cake. Another example of this kind of dust was on a process where names were engraved on plastic. There was no granulated dust. The laminated media on cylindrical bags allowed the exhaust to be re-circulated.
For assistance with such problems ... Dust Collection Solutions
Quality Air Management
Baghouse Dust Collector
Tuesday, November 10, 2009
Monday, November 2, 2009
Cement Plant Dust Collection
Although cement dust is relatively coarse and has optimum agglomeration properties, cement plants have some of the most demanding applications in the dust collection market.
First, all cement dust is dense and very abrasive. Even in the relatively less demanding application such as bag loading and bag unloading, these properties are important.
For many years, on the relatively light loading applications, shaker collectors were the preferred dust collectors. In fact the envelope collectors were very effective. The release of cement dust from shaker collectors was generally not a problem. In cylindrical bag collectors, the dust collected on the inside of the bag. The fastest moving air with its dust load was at the opening in the bag. There was a potential for wear near the bag entrance. If a bag developed a hole, the dust coming out of the tear would quickly abrade the surrounding bags. It seldom was possible to detect leaks until several bags, or even all the bags were damaged.
To filter a continuous process, off-line cleaning was necessary. On larger units, the collectors, in parallel sections or modules, were isolated and cleaned while maintaining flow through the remaining sections. On cement mills and other high load applications the collectors were usually preceded by cyclone pre-cleaners and the collectors often had dropout boxes or settling chambers. On these applications, shaker filters ran at filter ratios below 2:1. Air horns were often added to shaker collectors to improve cleaning and increase dust holding capacity.
In the late 60's the Fuller Corporation introduced their version of the pulse collector. This compartmented collector had large diaphragm valves that discharged into the clean air plenum. The burst of air agitated the filter bags, producing a thorough cleaning. More dust collected on a unit of filter area to allow handling of heavier dust loads. The name of this collector was "Plenum Pulse”. It was able to handle the heavier load for applications such as raw mills and finish mills. The first installations vented clinker cooler vent systems. A measure of the efficacy of this cleaning system was that the clean air plenum was built with heavier gauge metal because of weld failure with 12 gauge construction. While this collector was touted to be a pulse-jet collector, it was not. The compressed air did not create a reverse air jet. The collector operated more like a shaker than a reverse jet design. It produced more energy to clean the bags than existing shaker designs. This was especially necessary on the heavier loading processes.
Another effort to handle this high loading was the combination of shakers and reverse air cleaning systems, provided by "Norblo" a company that was based in Cleveland Ohio.
However in the late sixties, MiKroPulverizer (later renamed MikroPul) and their then licensee, FlexKleen, introduced the reverse pulsejet collectors. They were first applied to vent the raw and finish mills in the cement production process. The reverse jet collector was developed by MikroPul for their Pulverizers. These were similar to cement mills and were able to handle the heavier loads of the cement mills without pre-cleaners.
These collectors ran quite well, with filter lives exceeding three to five years. Then in 1969, when MikroPul's patent was challenged and declared invalid in court, many competitors copied their design. To counter the imitators, they made a major change in their design. The bag length went from six to ten feet. The pulse pipe orifice area was increased by the same ratio. Unfortunately, the venturi diameter was not changed. The velocity of the cleaning jet increased. It went from 15, 000 fpm to 25,000 fpm. Nobody recognized that the venturi velocity is proportional to the velocity of the dust leaving the bag towards adjoining bags during cleaning. In a dust like cement, it causes partial blinding and abrasive wear on adjoining rows during the cleaning pulse. Average pressure drops increased from 3 to 5.5 " wc. Bag lives were reduced by 50-60%. Compressed air usage went from about 0.5 SCFM per 1000 cfm of filtered air to 1.2 SCFM per 1000 cfm of filtered air. To counter these effects, the industry made some basic changes in selecting pulsejet collectors. The changes treated the symptom rather than the cause.
The development of the ULTRA-FLOW advanced technology design was able to remedy all the shortcomings of the 10 foot bag design. These designs will be discussed in future papers of this series.
Generally, the operators have chosen very conservative air to cloth ratios. Cartridge collectors are quite effective on less demanding applications.
Application Engineering Data Filter ratio - Cartridges
The belief was that more filter media (and associated filter ratio) made the selection more conservative. This idea is firmly entrenched in the cement Industry. This is generally true with pulse jet fabric collectors with high velocity cleaning jets in that it extends bag life. The fact is that the opposite is true with cartridges because of bridging across the pleats if the media is not cleaned. As dust accumulates in the valley of the pleat, it bridges. During the cleaning cycle the cleaning air looks for the easiest path from the inside to the outside of the filter cartridge. That path is above the bridge.
What contributes even more to this phenomenon is the fact that a certain volume of reverse air can only clean a certain amount of media. Because the cartridge may contain huge amounts of media that cannot be cleaned, the media not cleaned will plug. In most designs running at filter ratios of less than two, an operating cartridge may contain 10 to 40 pounds of dust. Table 1 illustrates the area of media that can be cleaned with various orifices and /or converging diverging supersonic nozzles.
Table 1
Orifice / Nozzle dia = area of media cleaned
0.250 in. = 5.5 / 8.8 sq.ft.
0.312 in. = 8.6 / 13.75 sq.ft.
0.375 in. = 12.3 / 19.8 sq.ft.
0.500 in. = 22 / 35 sq.ft.
0.750 in. = 49.5 / 79 sq.ft.
1.000 in. = 88 / 132 sq.ft.
1.500 in. = 198 / 376 sq.ft.
There are new advanced technology cartridge style dust collectors available today which incorporate wide pleat spacing, vertical cartridges and supersonic nozzles.
Dust Collector Selection
The best designs for a fabric media pulse jet collector on these applications are those offered by ULTRA-FLOW with low jet velocities and higher filter ratios The characteristics of these designs are listed below:
Find out about Ultra-Flow ... Advanced Technology Baghouse Dust Collectors
First, all cement dust is dense and very abrasive. Even in the relatively less demanding application such as bag loading and bag unloading, these properties are important.
For many years, on the relatively light loading applications, shaker collectors were the preferred dust collectors. In fact the envelope collectors were very effective. The release of cement dust from shaker collectors was generally not a problem. In cylindrical bag collectors, the dust collected on the inside of the bag. The fastest moving air with its dust load was at the opening in the bag. There was a potential for wear near the bag entrance. If a bag developed a hole, the dust coming out of the tear would quickly abrade the surrounding bags. It seldom was possible to detect leaks until several bags, or even all the bags were damaged.
To filter a continuous process, off-line cleaning was necessary. On larger units, the collectors, in parallel sections or modules, were isolated and cleaned while maintaining flow through the remaining sections. On cement mills and other high load applications the collectors were usually preceded by cyclone pre-cleaners and the collectors often had dropout boxes or settling chambers. On these applications, shaker filters ran at filter ratios below 2:1. Air horns were often added to shaker collectors to improve cleaning and increase dust holding capacity.
In the late 60's the Fuller Corporation introduced their version of the pulse collector. This compartmented collector had large diaphragm valves that discharged into the clean air plenum. The burst of air agitated the filter bags, producing a thorough cleaning. More dust collected on a unit of filter area to allow handling of heavier dust loads. The name of this collector was "Plenum Pulse”. It was able to handle the heavier load for applications such as raw mills and finish mills. The first installations vented clinker cooler vent systems. A measure of the efficacy of this cleaning system was that the clean air plenum was built with heavier gauge metal because of weld failure with 12 gauge construction. While this collector was touted to be a pulse-jet collector, it was not. The compressed air did not create a reverse air jet. The collector operated more like a shaker than a reverse jet design. It produced more energy to clean the bags than existing shaker designs. This was especially necessary on the heavier loading processes.
Another effort to handle this high loading was the combination of shakers and reverse air cleaning systems, provided by "Norblo" a company that was based in Cleveland Ohio.
However in the late sixties, MiKroPulverizer (later renamed MikroPul) and their then licensee, FlexKleen, introduced the reverse pulsejet collectors. They were first applied to vent the raw and finish mills in the cement production process. The reverse jet collector was developed by MikroPul for their Pulverizers. These were similar to cement mills and were able to handle the heavier loads of the cement mills without pre-cleaners.
These collectors ran quite well, with filter lives exceeding three to five years. Then in 1969, when MikroPul's patent was challenged and declared invalid in court, many competitors copied their design. To counter the imitators, they made a major change in their design. The bag length went from six to ten feet. The pulse pipe orifice area was increased by the same ratio. Unfortunately, the venturi diameter was not changed. The velocity of the cleaning jet increased. It went from 15, 000 fpm to 25,000 fpm. Nobody recognized that the venturi velocity is proportional to the velocity of the dust leaving the bag towards adjoining bags during cleaning. In a dust like cement, it causes partial blinding and abrasive wear on adjoining rows during the cleaning pulse. Average pressure drops increased from 3 to 5.5 " wc. Bag lives were reduced by 50-60%. Compressed air usage went from about 0.5 SCFM per 1000 cfm of filtered air to 1.2 SCFM per 1000 cfm of filtered air. To counter these effects, the industry made some basic changes in selecting pulsejet collectors. The changes treated the symptom rather than the cause.
- Filter ratios were drastically reduced. Bag life was increased and pressure drop was decreased to the 5 inch w.c. range.
- Pressure actuated cleaning systems were introduced. This kept the abrading and blinding of bags from cleaning pulses to a minimum. (The cleaning frequency and air consumption per 1000 cfm of filter air remained much higher than with the old six foot long bag designs.)
The development of the ULTRA-FLOW advanced technology design was able to remedy all the shortcomings of the 10 foot bag design. These designs will be discussed in future papers of this series.
Generally, the operators have chosen very conservative air to cloth ratios. Cartridge collectors are quite effective on less demanding applications.
Application Engineering Data Filter ratio - Cartridges
The belief was that more filter media (and associated filter ratio) made the selection more conservative. This idea is firmly entrenched in the cement Industry. This is generally true with pulse jet fabric collectors with high velocity cleaning jets in that it extends bag life. The fact is that the opposite is true with cartridges because of bridging across the pleats if the media is not cleaned. As dust accumulates in the valley of the pleat, it bridges. During the cleaning cycle the cleaning air looks for the easiest path from the inside to the outside of the filter cartridge. That path is above the bridge.
What contributes even more to this phenomenon is the fact that a certain volume of reverse air can only clean a certain amount of media. Because the cartridge may contain huge amounts of media that cannot be cleaned, the media not cleaned will plug. In most designs running at filter ratios of less than two, an operating cartridge may contain 10 to 40 pounds of dust. Table 1 illustrates the area of media that can be cleaned with various orifices and /or converging diverging supersonic nozzles.
Table 1
Orifice / Nozzle dia = area of media cleaned
0.250 in. = 5.5 / 8.8 sq.ft.
0.312 in. = 8.6 / 13.75 sq.ft.
0.375 in. = 12.3 / 19.8 sq.ft.
0.500 in. = 22 / 35 sq.ft.
0.750 in. = 49.5 / 79 sq.ft.
1.000 in. = 88 / 132 sq.ft.
1.500 in. = 198 / 376 sq.ft.
There are new advanced technology cartridge style dust collectors available today which incorporate wide pleat spacing, vertical cartridges and supersonic nozzles.
Dust Collector Selection
The best designs for a fabric media pulse jet collector on these applications are those offered by ULTRA-FLOW with low jet velocities and higher filter ratios The characteristics of these designs are listed below:
- Average velocity at bag opening = 10,000 feet per minute
- Bag opening (no venturi) = 4" diameter
- Jet volume = 740 CFM
- Bag diameter and length = 4 inches x 96 inches
- Bag area = 10 sq. ft.
- Filter volume rating per bag = 190 CFM
- Nominal filter ratio = 20 FPM
- Average pressure drop = 2 1/2 inches water column
- Average Air Consumption = 1/2 SCFM/1000 CFM of flow
- Average dust penetration at 5 gr./cu. ft. load = 0.0005 gr. / cu. ft.
Find out about Ultra-Flow ... Advanced Technology Baghouse Dust Collectors
Monday, June 15, 2009
Condensation in Dust Collectors
Let's look at three service reports which illustrate the problems of condensation and outline the possible solutions.
London, Ontario Installation;
Cartridge Dust collector retrofit on Plasma cutting stations
The client complained of having to service the cartridges every 1-2 days because they would plug up. The pressure drop across the collector would rise to 8-10 inches water column. The cleaning system was totally redesigned, and six 36” high ratio style cartridge filters replaced twenty-four 26” tandem cartridges. 80/20 paper blend cartridges were installed temporarily until special anti-pinch style polyester filters could be supplied. Within two days the paper cartridges blew apart, mostly at the closed end-cap. They did run the pulsed cleaning system at 100psi instead of 85psi, with no regulator on the line. However, that was not enough to rip the media apart, so, something else was the cause. Upon inspection of the cartridges, we observed that the media was dry but had the look of being wetted. Also there were watermark stains on the clean side of the media. There was an accumulator tank on the compressed air line leading to the collector. The maintenance people told us the accumulator was installed because the valve manifold wasn’t large enough to hold enough residual pressure during a pulse. The manifold was just fine. What was happening is that the air line was very long (over 200 feet) from the compressor to the collector. Moisture would condense in the line then drop out at two elbows, which was the low point just before going up to the manifold. This choked the line which made the manifold appear like it was too small, and then suddenly a slug of water would blow through to the valves and into the cartridges. We recommended taking out the accumulator tank and, just before the connection to the valve manifold, installing an air line coalescing filter, top quality dryer, and a regulator set for 85psi. We also recommended an automatic drain valve system on the manifold tank. The collector now runs continuously at 3-3.5inch pressure drop. The client says they’ve never been able to control the contaminants at the plasma stations so well since they installed the system 1.5 years prior to the retrofit.
Maine Installation; Energy Recovery from Trash and garbage.
This collector installation was venting a large room where garbage was dumped. Front-end loaders took this garbage and carried it to the hoppers that fed an incinerator. Steam was produced that fed a boiler. The pulse jet collector vented 65,000 ACFM at ambient conditions. It was running at a 15:1 filter ratio and at 2 “ water column from January to June. In June the pressure drop started to creep upwards about 1/8 of inch per week. This collector was well instrumented with continuous recording of wet bulb and dry bulb temperatures as well as pressure drop. We compared the pressure drop increases with the weather reports in the local newspapers. The increases occurred early in the morning on days when the wet bulb and dry bulb temperature were closer than 5 degrees F. There were several kinds of trash being handled in the facility. We recommended that they not load the wet trash into the incinerator until after 10:00 a.m. This stopped the rising pressure drop problem. Since they shut the system down on weekends we recommended that they clean the collector for two hours on Saturday afternoon with the outlet fan damper 90% closed. This was almost as effective as off line cleaning and the dust was not blown back into the loading room during the procedure. The dust collector ran for at least two years, at less than three inches water gauge pressure drop after implementing these recommendations.
General Comments The cleaning system was running at 85 psig. Under typical conditions the compressed air expands to critical pressure which is 37psig. beyond this pressure, the pressure to velocity conversion stops and from 37 psig to atmospheric pressure, 0 psig, the energy is turned to heat from turbulence. This nullifies the refrigeration cycle as the compressed air expands to critical pressure. This collector used converging diverging nozzles which had a complete conversion of pressure to energy so that the refrigeration cycle was reducing the temperature in the jet by approximately 5-8 degrees F.
Actually the turbulence below 37 psig causes some heat regain but the jet is still 5-8 degrees cooler despite this. Without the regain it would be about 9-12 degrees cooler. With a converging diverging nozzles the amount of cooling from expanded compressed air in the jet is a bit colder but the amount of induced air from the plenum is almost twice as much as with an ordinary orifice so the jet temperature is about 6-8 degrees cooler but not enough to make a difference. In Maine, the problem was mainly in the summer when the trash was wet from people dumping beer and other associated liquids. They did not have the problem in the winter when the trash was dry.
There were two other approaches that could have been used to counter the rising pressure drop:
1) Larger pulse valves and eliminating the nozzles. However, this would increase air consumption by over 35%.
2) Manifold heaters could be installed that would raise the temperature of the cleaning jet above ambient even to the point where wet garbage could be processed in high humidity conditions.
In either case, the collector could not handle vent volume where the gas entering the collector has condensed water droplets.
Low pressure compressed air, in the range of 7 to 22 psig is often employed for pulse jet cleaning systems. These have the same effect as the cleaning system with converging diverging nozzles since no turbulence occurs as complete expansion occurs in the orifice or nozzle. The best remedies are as follows:
1. Locate the low pressure compressor near the pulse valves and insulate the manifold leading to the pulse valves.
2. Use a manifold heater in the compressed air header, same as described above.
Other Comments and observations. There are many other installations in energy recovery plants that use high ratio reverse air fan collectors, The temperature regain on the reverse air fan is higher than ambient and eliminates condensation considerations described above.
East Tennessee Installation; Powder coating
This plant in the upper elevations in the mountains used a pulse jet collector to vent a powder coating operation that coated the internals of residential wash machines. This pulse jet collector started in July and ran until the middle of the winter when it developed a creeping rise in pressure drop characteristics. The wet and dry bulb spread was usually over 15 degrees F except early in the morning when it was about ten degrees. Investigation of the operation was conducted and we measured wet and dry bulb temperatures with a sling psychrometer mounted through a hole in the main vent duct. What we discovered is the booths were manually washed with a hot water hose every morning. At times the gas would go through the dew point for several minutes and then immediately go back to operation at a wide dew point spread. We recommended mounting a heater with a damper on a branch line to the vent system. The heater was triggered by pressure switches on the hot water hoses in each booth. This eliminated the creeping pressure drop problem permanently.
For information ... Dust Collector retrofits and Troubleshooting
London, Ontario Installation;
Cartridge Dust collector retrofit on Plasma cutting stations
The client complained of having to service the cartridges every 1-2 days because they would plug up. The pressure drop across the collector would rise to 8-10 inches water column. The cleaning system was totally redesigned, and six 36” high ratio style cartridge filters replaced twenty-four 26” tandem cartridges. 80/20 paper blend cartridges were installed temporarily until special anti-pinch style polyester filters could be supplied. Within two days the paper cartridges blew apart, mostly at the closed end-cap. They did run the pulsed cleaning system at 100psi instead of 85psi, with no regulator on the line. However, that was not enough to rip the media apart, so, something else was the cause. Upon inspection of the cartridges, we observed that the media was dry but had the look of being wetted. Also there were watermark stains on the clean side of the media. There was an accumulator tank on the compressed air line leading to the collector. The maintenance people told us the accumulator was installed because the valve manifold wasn’t large enough to hold enough residual pressure during a pulse. The manifold was just fine. What was happening is that the air line was very long (over 200 feet) from the compressor to the collector. Moisture would condense in the line then drop out at two elbows, which was the low point just before going up to the manifold. This choked the line which made the manifold appear like it was too small, and then suddenly a slug of water would blow through to the valves and into the cartridges. We recommended taking out the accumulator tank and, just before the connection to the valve manifold, installing an air line coalescing filter, top quality dryer, and a regulator set for 85psi. We also recommended an automatic drain valve system on the manifold tank. The collector now runs continuously at 3-3.5inch pressure drop. The client says they’ve never been able to control the contaminants at the plasma stations so well since they installed the system 1.5 years prior to the retrofit.
Maine Installation; Energy Recovery from Trash and garbage.
This collector installation was venting a large room where garbage was dumped. Front-end loaders took this garbage and carried it to the hoppers that fed an incinerator. Steam was produced that fed a boiler. The pulse jet collector vented 65,000 ACFM at ambient conditions. It was running at a 15:1 filter ratio and at 2 “ water column from January to June. In June the pressure drop started to creep upwards about 1/8 of inch per week. This collector was well instrumented with continuous recording of wet bulb and dry bulb temperatures as well as pressure drop. We compared the pressure drop increases with the weather reports in the local newspapers. The increases occurred early in the morning on days when the wet bulb and dry bulb temperature were closer than 5 degrees F. There were several kinds of trash being handled in the facility. We recommended that they not load the wet trash into the incinerator until after 10:00 a.m. This stopped the rising pressure drop problem. Since they shut the system down on weekends we recommended that they clean the collector for two hours on Saturday afternoon with the outlet fan damper 90% closed. This was almost as effective as off line cleaning and the dust was not blown back into the loading room during the procedure. The dust collector ran for at least two years, at less than three inches water gauge pressure drop after implementing these recommendations.
General Comments The cleaning system was running at 85 psig. Under typical conditions the compressed air expands to critical pressure which is 37psig. beyond this pressure, the pressure to velocity conversion stops and from 37 psig to atmospheric pressure, 0 psig, the energy is turned to heat from turbulence. This nullifies the refrigeration cycle as the compressed air expands to critical pressure. This collector used converging diverging nozzles which had a complete conversion of pressure to energy so that the refrigeration cycle was reducing the temperature in the jet by approximately 5-8 degrees F.
Actually the turbulence below 37 psig causes some heat regain but the jet is still 5-8 degrees cooler despite this. Without the regain it would be about 9-12 degrees cooler. With a converging diverging nozzles the amount of cooling from expanded compressed air in the jet is a bit colder but the amount of induced air from the plenum is almost twice as much as with an ordinary orifice so the jet temperature is about 6-8 degrees cooler but not enough to make a difference. In Maine, the problem was mainly in the summer when the trash was wet from people dumping beer and other associated liquids. They did not have the problem in the winter when the trash was dry.
There were two other approaches that could have been used to counter the rising pressure drop:
1) Larger pulse valves and eliminating the nozzles. However, this would increase air consumption by over 35%.
2) Manifold heaters could be installed that would raise the temperature of the cleaning jet above ambient even to the point where wet garbage could be processed in high humidity conditions.
In either case, the collector could not handle vent volume where the gas entering the collector has condensed water droplets.
Low pressure compressed air, in the range of 7 to 22 psig is often employed for pulse jet cleaning systems. These have the same effect as the cleaning system with converging diverging nozzles since no turbulence occurs as complete expansion occurs in the orifice or nozzle. The best remedies are as follows:
1. Locate the low pressure compressor near the pulse valves and insulate the manifold leading to the pulse valves.
2. Use a manifold heater in the compressed air header, same as described above.
Other Comments and observations. There are many other installations in energy recovery plants that use high ratio reverse air fan collectors, The temperature regain on the reverse air fan is higher than ambient and eliminates condensation considerations described above.
East Tennessee Installation; Powder coating
This plant in the upper elevations in the mountains used a pulse jet collector to vent a powder coating operation that coated the internals of residential wash machines. This pulse jet collector started in July and ran until the middle of the winter when it developed a creeping rise in pressure drop characteristics. The wet and dry bulb spread was usually over 15 degrees F except early in the morning when it was about ten degrees. Investigation of the operation was conducted and we measured wet and dry bulb temperatures with a sling psychrometer mounted through a hole in the main vent duct. What we discovered is the booths were manually washed with a hot water hose every morning. At times the gas would go through the dew point for several minutes and then immediately go back to operation at a wide dew point spread. We recommended mounting a heater with a damper on a branch line to the vent system. The heater was triggered by pressure switches on the hot water hoses in each booth. This eliminated the creeping pressure drop problem permanently.
For information ... Dust Collector retrofits and Troubleshooting
Thursday, February 19, 2009
Static Electricity and Dust Collector Systems
General Considerations
The effects of static electricity on the collection of dry particulate in fabric collectors is rather simple but misunderstood. For the most part, cartridge dust collectors experience the same issues.
First we must consider the cause of static charge build up in a collector. It occurs because the dust being collected is akin to a capacitor in an electronic circuit. In this day of computer chips the designer may not be familiar with this phenomenon. The capacity has two conductive plates separated by a layer of insulating material that has high enough insulation values that the static charge remains for relatively long periods. The charge can be removed by grounding one side of the capacitor. The charges then drain.
In dust collectors where the dust forms in the filter cake, the static charges may enter the collector on the surface of dry particulate dust. If the dust has high dielectric resistance properties, it can accumulate and build up in the filter cake. It can be viewed as many particles each carrying a static charge and acting like a miniature capacitor. The static charge will then build up on the surfaces and may reach a high enough level where a spark can be produced. This spark can trigger the explosion of explosive dusts.
Mechanical Cleaning (Shaker) Dust Collectors
In a fabric collector with a mechanical shaking mechanism to remove the dust, the collector is most vulnerable during the cleaning process. The dust is shaken from the filter bags in the process of shaking the cake, sparks sometimes are produced. Invariably, the dust/ gas mixture passes between the upper and lower explosive limits. A serious explosion may occur.
Usually these collectors will have explosion vents which relieve the high pressures that are generated in an explosion, presumably keeping the housing from being damaged and protecting the operating personnel near the dust collector.
In an attempt to keep this static charge from building to threatening levels, measures are included in an attempt to bleed this charge to ground. These include one or more of the following:
1) Sewing in grounding wires into the filter media.
2) Impregnating carbon or other conductive coating into the filter cloth.
These often give the designer a false sense of security in applying these to dust collectors. As explained above the dust, itself, insulates the charge and it remains in the cake until it reaches a point where a spark is generated. If the dust concentration is above the lower explosive limit and below the upper explosive limit, an explosion can occur. Fortunately, generation of the spark may not occur if the timing of the spark and dust concentration level do not coincide. An explosion does not occur in these cases.
Continuous Cleaning Reverse Jet Pulsed Dust Collectors
When dust, with the same properties described above, is vented in the same operations, using a reverse pulse jet cleaning system, the danger is considerably diminished unless the pulsing is applied in “off line” cleaning mode where the fan is stopped.
These collectors clean the bags by injecting air from the clean air plenum backwards through individual bags as the flow continues through the collector. This cleaning agitates the filter cake so the static charges are dissipated.
The danger of explosion occurs when the dust concentration coming into the collector reaches a level between the lower and upper explosive limit concentrations. This is highly unlikely but we recommend that properly sized explosion vents are installed which normally coincides with the requirements of insurance underwriting firms.
The explosions can occur when there is dust build up in ducts especially when long horizontal runs are encountered. The spark can be generated in ducts and the explosion front can travel down the duct into the dust collector, igniting a secondary explosion as the concentration in the collector housing is driven above the lower explosive limit for that dust. Even with no build up in the ductwork, an upset can occur in the process which generates sufficient dust concentrations.
One method of nullifying the possibilities of danger due to duct build up is to install an automatic booster / duct cleaner device. This booster can serve to automatically clean out any drop out in long horizontal duct runs.
Another phenomenon can affect of dust collector systems, is where the dust has high dielectric properties and the dust, because of static charges, will build up on the outside bend of an elbow. This dust can trigger an explosion if this dust is also flammable and explosive. Some examples of dust where this problem is often a factor are toners for copy machines and electrolyte powder used in alkaline batteries. The solution is to insert a pulsed air jet that agitates the built up dust that dissipates the charge. Some dry powder coating compounds are also subject to static charge build up in powder coating systems.
Read more about ... Booster / Duct Cleaner, and Quencher spark arrestor
The effects of static electricity on the collection of dry particulate in fabric collectors is rather simple but misunderstood. For the most part, cartridge dust collectors experience the same issues.
First we must consider the cause of static charge build up in a collector. It occurs because the dust being collected is akin to a capacitor in an electronic circuit. In this day of computer chips the designer may not be familiar with this phenomenon. The capacity has two conductive plates separated by a layer of insulating material that has high enough insulation values that the static charge remains for relatively long periods. The charge can be removed by grounding one side of the capacitor. The charges then drain.
In dust collectors where the dust forms in the filter cake, the static charges may enter the collector on the surface of dry particulate dust. If the dust has high dielectric resistance properties, it can accumulate and build up in the filter cake. It can be viewed as many particles each carrying a static charge and acting like a miniature capacitor. The static charge will then build up on the surfaces and may reach a high enough level where a spark can be produced. This spark can trigger the explosion of explosive dusts.
Mechanical Cleaning (Shaker) Dust Collectors
In a fabric collector with a mechanical shaking mechanism to remove the dust, the collector is most vulnerable during the cleaning process. The dust is shaken from the filter bags in the process of shaking the cake, sparks sometimes are produced. Invariably, the dust/ gas mixture passes between the upper and lower explosive limits. A serious explosion may occur.
Usually these collectors will have explosion vents which relieve the high pressures that are generated in an explosion, presumably keeping the housing from being damaged and protecting the operating personnel near the dust collector.
In an attempt to keep this static charge from building to threatening levels, measures are included in an attempt to bleed this charge to ground. These include one or more of the following:
1) Sewing in grounding wires into the filter media.
2) Impregnating carbon or other conductive coating into the filter cloth.
These often give the designer a false sense of security in applying these to dust collectors. As explained above the dust, itself, insulates the charge and it remains in the cake until it reaches a point where a spark is generated. If the dust concentration is above the lower explosive limit and below the upper explosive limit, an explosion can occur. Fortunately, generation of the spark may not occur if the timing of the spark and dust concentration level do not coincide. An explosion does not occur in these cases.
Continuous Cleaning Reverse Jet Pulsed Dust Collectors
When dust, with the same properties described above, is vented in the same operations, using a reverse pulse jet cleaning system, the danger is considerably diminished unless the pulsing is applied in “off line” cleaning mode where the fan is stopped.
These collectors clean the bags by injecting air from the clean air plenum backwards through individual bags as the flow continues through the collector. This cleaning agitates the filter cake so the static charges are dissipated.
The danger of explosion occurs when the dust concentration coming into the collector reaches a level between the lower and upper explosive limit concentrations. This is highly unlikely but we recommend that properly sized explosion vents are installed which normally coincides with the requirements of insurance underwriting firms.
The explosions can occur when there is dust build up in ducts especially when long horizontal runs are encountered. The spark can be generated in ducts and the explosion front can travel down the duct into the dust collector, igniting a secondary explosion as the concentration in the collector housing is driven above the lower explosive limit for that dust. Even with no build up in the ductwork, an upset can occur in the process which generates sufficient dust concentrations.
One method of nullifying the possibilities of danger due to duct build up is to install an automatic booster / duct cleaner device. This booster can serve to automatically clean out any drop out in long horizontal duct runs.
Another phenomenon can affect of dust collector systems, is where the dust has high dielectric properties and the dust, because of static charges, will build up on the outside bend of an elbow. This dust can trigger an explosion if this dust is also flammable and explosive. Some examples of dust where this problem is often a factor are toners for copy machines and electrolyte powder used in alkaline batteries. The solution is to insert a pulsed air jet that agitates the built up dust that dissipates the charge. Some dry powder coating compounds are also subject to static charge build up in powder coating systems.
Read more about ... Booster / Duct Cleaner, and Quencher spark arrestor
Subscribe to:
Posts (Atom)